#Change mac address on terminal emulator serial
#Change mac address on terminal emulator software
#Change mac address on terminal emulator free

The flow control used to protect against data overruns, uses data bytes as control characters.

#Change mac address on terminal emulator software

XON/XOFF protocol: Software handshaking.This is read by the sender at the CTS input, indicating it is clear to send the data. When a receiver is ready for data, it asserts the RTS line indicating it is ready to receive data. RTS/CTS: Hardware hanshaking This method uses hardware lines RTS (Request to Send) and CTS (Clear to Send).Transmission control to pause data transfer, when receiving buffer of the opposite device if full. Specifies how the system uses the parity bit to check for transmission errors. Data size specifies the number of data bits in a character.Baud specifies the transmission rate in bauds.

#Change mac address on terminal emulator serial

Name define the number of the serial communication port.

Display special characters (in ASCII, HEX or DEC).

Send and display messages or commands to and from remote device.

Set and display the value of the signal on each modem line (i.e.

Set the mode of operation (Free, PortStore test, Data, Setup).

Set the parameters of the connection (speed, parity, handshake).

It's similar to the Hyperterminal, some functions extended. The Serial tab of the Hercules utility can be used as a simple serial port terminal for the RS-232 standard. If the Port field of the device (the port where the device listens to) is not set to 23 this connection will fail.Д¬licking this button will open the page of the device in a WEB browser, if the device has a WEB server running. Press enter to see the parameters that you can set.Д¬licking this button will automatically open a Telnet connection with the device (port 23). In the TCP Client menu you will see the device configuration mode.

Enable TCP setup: Checking this box enables the configuration of the device with the TCP Client.Д¬licking on this button will automatically open a connection to the device through port 99.

Enable NVT: Checking this box enables to send to the device NVT commands.

TCP TEA authorization: Checking this box enables encrypted communication with the device using TEA.

If this condition is valid, you can access the device (AND is binary multiplication). Security can be greatly enhanced by setting a fixed address or a suitable restrictive mask that disallow communication with unauthorized parties. This mask restricts addresses that can communicate with the device. More details to the IP Filter you can find in the device's manuals, include examples and counting formulas. This value must result from multiplying the remote IP address and the restriction mask (option N), otherwise the device does not react. IP address of a network or computer that is allowed to communicate with the device. The IP address of the PC, router or switch interface, etc., with which the device is directly connected. It must be the same for all the devices in the network segment. For the Connect with TCP Client button to work it has to be set to 23 (Telnet). This field displays the port the device (operating as server) listens to. This field displays the IP value of the respective device which has the MAC address highlighted in the Modules MAC list. Clicking on a particular MAC address will highlight it and will show the parameter values of the respective device in the Required parameters field. In this window will be displayed the MAC addresses (a.k.a physical addresses) of the devices connected to your network segment. Otherwise the changes will not take place. The parameter changes are applied by clicking on this button.

3x quick button (TCP Setup, TCP data communication, WWW Browser)Д¬licking on this button will find all the devices on your network segment.NVT enable (for the remote serial port devices).TEA authorisation enable (useful for the security reasons).Define IP filter range (useful for the security reasons).Check and assign main network parameters (IP address, IP mask ans Gateway).

List of all devices on the network segment (MAC list).

Search for the devices over UDP broadcast.

In this window you can assign the IP address to compatible devices ( PortBox, PortStore, PortStore2, I/O Controller, Charon 1 module, Poseidon etc.) Parameters : This tab is to be used with HW-group devices only.

#Change mac address on terminal emulator free

The Hercules SETUP is compatible with our free Virtual Serial Port, you can debug applications connected to remote serial port using Windows 2000 or higher.

Test mode (TCP/IP terminal with TEA authorization support and NVT (Network virtual Terminal) parser for remote I/O pins control.

UDP Config utility (IP, Port, MASK, GW setting).

TCP/IP Client terminal (similar to 'Telnet').

Serial port terminal (COM5 and higher support).

Hercules is great utility if you are working with the serial and Ethernet devices & interfaces.